Appearance
Top Bar & Transport
New in Orbit 1.5.10
A new top bar: one transport, a bigger timecode card with pre-roll and the pointer's time, Insertion Follows Playback, and the open file named at the top left. The window's title bar is gone, and the top bar uses that space.
The top bar runs across the top of the window on every page. From left to right it shows what's open, the transport and the timecode card in the centre, and the master fader with Orbit's CPU and memory use on the right.
What's open
The top-left corner, around the window's traffic lights, says what you're working on:
- The mode, on the same row as the traffic lights: PREVIEW in blue when a file is open on its own, or SESSION in yellow when a session is open, followed by the session's name. See Preview Mode and Sessions.
- The file, beneath the traffic lights: the name of the file playing, and its type, ADM or IAMF. A long name is shortened in the middle, so it never squeezes the transport. With nothing loaded in Preview, it reads No File Loaded.
In Orbit Pro, click PREVIEW to save the open file as a session (the same as File ▸ Create Session from Preview…).
To open a file, choose File ▸ Open File… (⌘O).
The transport
Play, Stop, Loop and Insertion Follows Playback sit together in one cluster in the centre of the bar:
| Button | What it does |
|---|---|
| IFP | Insertion Follows Playback — where Stop leaves the playhead. See below. |
| Loop | Turns looping on or off. It needs a loop region first; with no region, its tooltip says Set loop points on timeline first. The button turns yellow while looping is on. |
| Play / Pause | Starts playback, or pauses it. Space does the same. |
| Stop | Stops playback. Press it again while stopped to go back to the start. |
In Orbit Pro, when a session has tracks in its playlist, Previous Track and Next Track sit at either end of the cluster to skip between them.
New in Orbit 1.5.10
Looping is now in Orbit Standard as well as Pro: loop regions, the Loop button, and the I, O and L shortcuts. See Loop regions.
Insertion Follows Playback (IFP)
IFP decides where the playhead goes when you stop:
- Off (the default) — Stop returns the playhead to where you pressed Play, so the next Play repeats the same passage. Handy for checking one moment over and over.
- On — Stop leaves the playhead where you stopped, like a tape machine.
Either way, press Stop a second time to go to the start of the file. Pausing with Space follows the same rule.
The edit cursor
Every timeline has an edit cursor, a blue line where you last clicked:
- Stopped, a click on the timeline puts the edit cursor and the playhead there, and Play starts from it.
- Playing, a click moves the edit cursor and playback carries on. With IFP off, Stop then returns to the edit cursor.
The ruler always scrubs the playhead.
The timecode card
The card beside the transport shows three lines of time, all lined up in columns:
- Position — where the playhead is, over the file's total length.
- Loop region — the region's start, end and length. Dashes when no region is set.
- Edit cursor — where the edit cursor sits, in blue.
The card turns yellow while looping is on.
Double-click a time to type it. Double-click the position to move the playhead, or a region's start or end to set it. Type the digits only: they fill in from the right and the colons appear on their own. Press Return to apply, or Esc to cancel.
Right-click the card for its settings, without opening Preferences:
- Timecode Format — HH:MM:SS or SMPTE.
- Frame Rate — the rate SMPTE timecode counts at.
- 2-Pop Preroll — the 2-second leader offset on SMPTE timecode.
- Pre-Roll, and Pre-Roll Length (1, 2, 3 or 5 s) — see below.
These are the same settings as in Preferences ▸ Timecode, so changing one changes the other.

Pre-roll (PRE)
With pre-roll on, Play starts a few seconds before where it would otherwise start — before the loop start when you play a loop, or before the playhead. It's a run-up, so you hear what leads into the passage you're checking.
- Click PRE to turn pre-roll on or off. It glows orange while it's on.
- Double-click the length beside PRE to type a new one. The default is 2 seconds.
While pre-roll is on, orange rails on the timeline show where Play will start: a thin line along the top of the loop band, back from the loop start and from the edit cursor. When the two would overlap, only the one the next Play uses is shown.
Pre-roll isn't the 2-pop. The 2-pop only changes how SMPTE timecode is labelled; pre-roll changes where playback starts.
Pointer time (PTR)
PTR, under PRE, shows the time under the mouse pointer as you move it over a timeline, in the same format as the playhead. It shows dashes when the pointer is off the timeline.
The right of the bar
- Background work — while files import or a waveform builds, a small readout shows what's happening and how far along it is (for example IMPORTING 2 and a percentage, or SCANNING). An import that fails shows IMPORT FAILED in orange. Click the readout for the list of every import, where you can cancel, retry or remove each one. The readout disappears when nothing is running.
- Master fader — overall output level. Option-click it to reset it to 0 dB.
- CPU and MEM — Orbit's own CPU and memory use, one above the other. CPU turns orange, then red, as it climbs.

Tooltips
Rest the pointer on a transport or top-bar control to see what it does. To turn these tooltips off, go to Preferences ▸ Appearance ▸ Tooltips and switch off Show tooltips. See Appearance.
See also
- Menus & Shortcuts — every transport shortcut, including the loop keys.
- Timeline View — the timeline toolbar, lane meters and playhead scrolling.
- Overview Waveform View — the ruler, loop regions and the edit cursor on the Overview.
- Timecode Preferences — the same timecode settings as the card's right-click menu.
